category：Environmental protection / date：2022-02-22 00:46:19 / browse：417 / comment：5
The quality of the solid wood composite board made of high-grade flowers, plants and trees can also be divided into good and bad. Therefore, it is best to select the solid wood composite floor guaranteed by a well-known brand, which can not only ensure the quality, but also deal with the problems of the store.Structure: artificial surface material, artificial basic, wood slag plus strong glue, additives and additives.After the high-pressure suppression of the panel splicing machine, it gets rid of the defect of poor wood reliability.Houston,The floor shall try to avoid direct irradiation of strong light and long-term heating of high-temperature artificial light source, so as to avoid early dry crack and aging of the floor surface.Close the window when it rains so as not to wet the floor.Also pay attention to indoor ventilation, emit indoor moisture and maintain normal indoor temperature, color film texture layer and substrate layer.Its base material is a composite plate made of stone powder and thermoplastic polymer materials mixed evenly and extruded at high temperature after stirring.At the same time UV layer, it has the properties and characteristics of wood and plastic to ensure the strength and toughness of the floor.Lets take a look at the advantages of SPC floor.A good paper cutter can be used to cut at will. In addition, it can be composed of raw materials with different colors. It is especially suitable for floor tile mosaic ground. It can be composed and matched at will. It makes full use of the intelligence of interior designers to achieve the most ideal practical effect of decoration design;It is enough to turn your ground into handicrafts, full of plastic art atmosphere.Radauti,Precautions for solid wood floor installation : prevent keel from drying.In short, pollution resistance, corrosion resistance, moisture resistance, simple construction, convenient maintenance and low price, it also adds the advantages of comfortable foot feeling, warm in winter and cool in summer of wood floor, narrowing the gap between wood floor and wood floor. No wonder floor leather will be so popular.If you are also worried about the shortcomings of wood flooring you might as well consider floor leather materials.Plastic floor leather has the advantages of light weight, elasticity,HoustonSES floor manufacturer, good mechanical strength, good foot feeling strength, foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance,HoustonNew waterproof floor, small water absorption good insulation, self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, factories with high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor leather is m ~ m, the width is mm ~ mm, and the total thickness is mm (household) ~ mm (public building).First, pay attention to the size of the board, and try to choose a wide board with a length of cm, a width of -cm and a thickness of cm, or a standard board with a width of cm and a thickness of cm.
Remove spots and stains with special floor cleaner.Do not clean with items with damaging properties, nylon friction pads and bleaching powder. Remove the original open putty from the edge, seal the edge again, apply primer on the whole floor and wait for drying.Advantages: of course, the grain is comfortable, wear-resistant, corrosion-resistant, moisture-resistant, flame retardant, and the maintenance is better than that of solid wood.Suitable soil temperature, can also be paved in the kitchen.Where is itFourth, it is mainly the veneer thickness (decorative board thickness). The multi-layer solid wood floor has ,-, and the new three-layer solid wood floor has , to , mm.The joint of the floor adopts the form of latch, which controls the vertical displacement of the floor and the horizontal displacement of the floor;The original tenon and groove type, which is often called tongue and groove floor, can only control the vertical displacement of the floor.No matter how early the wooden floor plate is, there is no tenon and groove at the joint, and the displacement in any aspect can not be controlled. Therefore, the floor plate often tilts up and stumbles when walking, which is inconvenient.The surface is treated with special technology, without air holes and water impermeability. It is no problem to shop in the areas where toilets and kitchens communicate with water.No, it will not be like the ordinary wooden floor. Once it bubbles, it will deform and bubble or it will become moldy due to high humidity.
Only ~ mm thick.Quality risk,Since the wear-resistant layer on the surface of the strengthened ground has good wear resistance, compression resistance, impact resistance, fire and flame retardancy, chemical pollution resistance and other properties, in daily use, it only needs to be cleaned with a twisted dry rag, mop or vacuum cleaner. If the ground is greasy and dirty, it can be wiped with a rag and detergent.Because of its special structure, solid wood composite floor has low requirements for wood and can make full use of materials, so its price is much cheaper than solid wood composite floor.The combination of hardness and softness.The wood floor in the living room should be made of boards without knots, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better, because their lines are beautiful and clear and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly, the wood board shall be processed into the length and width coordinated with the room size according to the room size, and the floor shall be cleaned before laying.When laying, draw the center point and vertical and horizontal vertical lines of the room, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.Houston, The packaging is rough, the printing quality of the publicity album is poor, the attributes are pieced together, and the slogan selling points are set by set, which often misappropriates the album attributes of large companies. Silencing, comfortable and elastic walking feet, not easy to be injured when fallingFirst, pay attention to the size of the board, and try to choose a wide board with a length of cm, a width of -cm and a thickness of cm, or a standard board with a width of cm and a thickness of cm.